UWF supports paging to increase virtual memory, if the page file exists on an unprotected volume. When paging is used together with a RAM-based overlay, the uptime of the system can be significantly increased. The overlay does not mirror the entire volume, but dynamically grows to keep track of redirected writes. UWF does not support the use of fast startup when shutting down your device. If fast startup is turned on, shutting down the device does not clear the overlay.
UWF does not support Storage Spaces. On a computer on which UWF is enabled and used to protect drive C , you cannot permanently set the date and time to a past time. If you make such a change, the original date and time settings will be restored after the computer restarts. To work around this issue, you must disable UWF before you change the date and time. To do this, run uwfmgr. UWF is an optional component and is not enabled by default in Windows You must turn on UWF before you can configure it.
You can choose where the overlay is stored RAM or disk , how much space is reserved, whether the overlay persists after a reboot.
To increase uptime, set up monitoring to check if your overlay is filling up. To learn more, see UWF Overlay location and size. Add Full screen mode, the "F" key will toggle the full screen mode on and off. Revamp the way the audio and video format is set, it no longer relies on a persistent IAMStreamsConfig interface now, it queries the graph each time it needs it.
Alter the way Key input is done, now get the key value from the actual message data instead of using GetKeyState. Don't switch focus to the stats window when dragging the main window. Make Channel spin control change channels in real time on the Tuner Tab of the setting dialog. The audio mixer input settings are now stored in the profile file and default settings when saved and reloaded ,these include the volume and what input was selected.
Added checking so you can not select a master stream for the AVI when using the resample audio option. Do not act on messages from the FilterGraph to the application when not capturing. Add some logging capabilities, start with -logging to turn on logging of actions to actionLog.
Rename a lot of the classes to conform with some sort of standard. Only allow one instance of the application to run at any one time. Bug Fixes Fixed a bug when using audio resample, if you captured stopped and then captured again the Audio resample filter would not be activated. Thus the second capture would not have audio resampling turned on.
If there are no video amp settings in the INI file do not try to set them to any default values just leave them alone. Revamp the AV Sync options, they are easier to understand now, also added a resample audio to option for when you know how much you need to alter the audio stream to match the video manually.
Bugs Fixed Audio bug where capturing without re sampling would fail with a "Could not render audio stream" error. Fixed a bug when capturing compressed audio without re-sampling the audio, the audio would not be compressed. Added a lot of code to test for error conditions, this will help people with cards and drivers that do not have the full WDM tuner interface etc.
Added output file name override command line option. Brightness, Hue, Contrast, Saturation and Colour Enabled Fixed a bug with saving the tuner settings in the profile file correctly. It will override any settings in the configuration files INI.
Added Mono to the Audio Resample Filter, the only limitation on this filter now is the audio has to be 16 Bit. Changed the way the input select works, now sets this last in the list of things to set.
Added an Audio Scope to help with setting up the audio levels. Changed Layout of the Settings and Options tabs. VCR file, this is now fixed. See the following URL for more information on this bug. The FlowMeter now uses Sample time stamps to calculate the rate of video and audio streams for AV sync, there is a bug with the precision counters with some motherboards and this was causing problem with the Resample option.
Thanks to Moitah for bringing this to my attention. This new approach should work better. Stats dialog is now more compact. Log AV diff settings to "AVdiff. The main difference is all the settings are now in a properties sheet presented in a TAB selection dialog. All installed Video filters with at least one input pin and at least one output pin are scanned and added to the list of available filters for pre filtering, if you have the CPU power why not use it :- Lots of code clean up, removed a lot of old UI code that is no longer used, removed a lot of legacy stuff relating to device adding removing, I figure that if you add a new device you can close the app and open it again to scan for new devices.
Fixed a few small bugs with "Stats Docking" now should work on XP. Version 1. For the time being there are 2 dropped frame counters on the Capture Stats page, Dropped is the normal counter supplied by the capture driver and Dropped2 is the new dropped frame counter implemented in the FlowMeter filter.
In addition to the new dropped frame interface you can now get a list of the dropped frames from a capture by selecting the "Show Dropped Frames" from the Capture menu, this will display what frames were dropped in the last capture. The FlowMeter filter now takes into account dropped frames when working out the Frame rate of a video stream, this is important, if you have lots of dropped frames it would effect your frame rate and thus mess up the rate control and audio resample system.
This new approach should make the AV sync option work better when you have dropped frames. Added the SyncUsingStreamOffset setting under the capture menu, this should help people with large latency audio cards or video capture cards. There is a heap of docs on the Microsoft site about this and live streams: msdn.
Added a disk space free gauge on the status dialog. Revamped the AV sync process, the feedback loop was prone to errors so it now uses a set ratio based on the video to audio stream differences. Comment: This is not really a filter, but it will help diagnose most DirectShow related problems when trying to play a Matroska file. Please use this tool if you can't play MKV files in Windows Mediaplayer, even after successful matroska pack installation, and send us the log file.
It can decode most video and audio compression methods existing today and all in a single, powerful DirectShow filter for Windows Mediaplayer. There are later version of ffdshow out there than this one, however, they are not distributed from their official homepage on sourceforge anymore.
Google is your friend Comment: This a DirectShow muxer filter. To use in GraphEdit, connect the filters outputting compressed data to the in pins of the Matroska Muxer.
Then connect the out pin to the File Writer filter. Comment: THE standard matroska creation and editing tool, all recent builds supports the new lacing method, so make sure to have a recent splitter. The GUI is called mmg. Comment: Project is more or less abandoned, nobody is working on it actively. Also, it can't support most of the modern MKV files anymore. Since version 1. Please update to the latest bugfix, build Better use mkvtoolnix or avi-mux GUI.
Comment: Definitely one of the best MKV creation and editing tools out there. Just the name sucks
0コメント